In Qatar, engineers replaced imported road stone with steelmaking waste in a full-scale asphalt section; 3 years later, the recycled road resisted deformation better

Engineers in Qatar utilized steel slag from steel production as a substitute for conventional asphalt materials. The trial included monitoring a road section built with steel slag over three years. Results indicated that the recycled asphalt showe...

An AI-generated representative image of engineers inspecting the steel slag asphalt road during long-term performance monitoring. (Image credit: ChatGPT)

Industrial waste normally ends up in stockpiles or landfills instead of being used in thousands of vehicles. However, engineers in Qatar took that risk by replacing part of the stone used in asphalt road construction with waste from steel manufacturing. Three years on, the recycled road showed results.

Engineers in Qatar tested whether steel slag, a byproduct of steelmaking, could replace gabbro, the hard rock commonly used in the country's asphalt roads. They did not stop at testing in a laboratory and instead made a full-scale trial section and monitored its performance for three years. The results, published in the journal Case Studies in Construction Materials, showed that the recycled asphalt resisted permanent deformation better than conventional pavement while performing just as well in other key measures.

From steelmaking waste to road material


Steel slag is the rock-like residue left after impurities are removed from molten steel during production. While it is known for its strength and durability, engineers have been hesitant to use it in roads due to the presence of free lime or magnesium oxide in some slags, which can expand when exposed to moisture and cause damage to the pavement over time. Before using the material in asphalt, the research team carried out a series of laboratory tests to determine whether the slag was stable enough for road construction. They compared its physical, chemical, and volumetric characteristics, conducted expansion and weathering tests, and developed asphalt mixes with various steel slag sizes and replacement ratios. The processed slag produced very little expansion, providing the researchers with the opportunity to take the tests beyond the laboratory and test the slag in a full-scale road.

Building and monitoring a real road

557th_ERHS_paves_the_way_140219-Z-QD538-085 (1)
<p>Road paving in Qatar represents the full-scale field trial used to evaluate recycled steel slag in asphalt pavement. (Image credit: Wikimedia Commons)<br></p>
Beyond the lab experiments, the team built a real asphalt test section in Qatar .using steel slag to replace part of the imported gabbro crushed stone used in the country's road network. As a control, the team constructed a conventional asphalt section using natural aggregate. The researchers inspected both pavements immediately after construction and after three years of use. They tested for rutting, or the permanent deformation from repeated traffic loads, and moisture susceptibility and asphalt binder aging, two variables that have a significant impact on pavement durability. After three years, the steel slag pavement showed greater resistance to rutting than the conventional asphalt while showing no measurable decline in moisture resistance or binder performance. The results indicate that the recycled aggregate was not affected by long-term exposure to the hot desert conditions in Qatar.
ADVERTISEMENT

Why aggregate size mattered

The study also showed that not every steel slag mixture behaved the same. Because steel slag has a rougher and more porous surface than natural aggregate, asphalt mixtures containing higher amounts of slag required additional bitumen to properly coat the particles.

Particle size also made a difference. Mixtures made with coarse steel slag performed better than those with finer slag in the Marshall mix design test, a common engineering test used to assess asphalt stability, flow, density, and air voids before road construction. The results indicate that successfully using steel slag requires not only replacing part of the natural aggregate, but also adjusting the asphalt mixture design to account for the material's unique properties.

Reducing waste while cutting dependence on imports
ADVERTISEMENT

Qatar has high demand for imported gabbro for road construction while also producing steel slag through its industrial sector.The field trial suggests that, when properly processed, the byproduct could replace some imported aggregate while maintaining pavement performance throughout the trial.

The researchers say that longer-term monitoring will need to be done, as roads are used for decades and are exposed to heavy traffic and extreme heat. Nevertheless, the study provides field evidence, not just laboratory results, that steelmaking byproduct waste can be a sustainable road construction material in actual operating conditions, offering a new application for a byproduct of the manufacturing process and a substitute for imported construction stone as a durable material.
Download
The Economic Times Business News App
for the Latest News in Business, Sensex, Stock Market Updates & More.
Download
The Economic Times News App
for Quarterly Results, Latest News in ITR, Business, Share Market, Live Sensex News & More.
READ MORE
ADVERTISEMENT

READ MORE:

LOGIN & CLAIM

50 TIMESPOINTS

More from our Partners

Loading next story
Business News › News › International › US News › In Qatar, engineers replaced imported road stone with steelmaking waste in a full-scale asphalt section; 3 years later, the recycled road resisted deformation better
Text Size:AAA
Success
This article has been saved

*

+